How to reset a Parrot MKI9200
This seems to be a common question, so here is the method to reset the Parrot MKi9200.
Sometimes it may be necessary to reset the MKi9200. Resetting will remove all paired devices and reset settings back to factory standard. It should be noted that “mute on streaming” option is not altered by a factory reset.
Please note that the remote control MUST be able to be used with the MKi9200. If the remote does not work you will not be able to reset the MKi9200. All MKi remotes contain a CR2032 battery and it is common for people to forget to change them – they typically last a year to 18 months in normal use.
Reset procedure:
1. Turn on the MKi9200
2. Press the centre button on the remote and rotate until you get to “Settings”
3. Enter Settings menu and navigate down to “Advanced Settings”
4. When in Advanced Settings menu select “Factory Reset” and press the centre button on the remote.
5. The MKi9200 will now re-boot. Please note that sometimes it will refuse to erase memory. Simply turn off the MKi9200 and try again.
6. After the re-boot it may be necessary to set the language version again. Simply select the required language from the listed options and press remote control centre button to set the language. The MKi9200 will then re-boot again.
Different software versions of Parrot MKi9200’s may operate slightly differently. If you have a Version 2 control box you can update this to the latest version for that version – V2.20
If you have a version 3 control box you MUST NOT update the firmware. There are no updates for this version.
Share this post
Leave a Reply
This site uses Akismet to reduce spam. Learn how your comment data is processed.
Comments (28)
Hi, I have the mki9200, and whenever I start to make a call, it displays ‘call’ instead of the person I’m calling, then it shuts off, and restarts again. Iv disconnected and reconnected my phone and reset to factory settings, but it’s still doing it, any ideas what it could be? Thanks
Hello Melanie,
As a test disable phone book sync in your phone’s Bluetooth settings.
If it then stays connected, troubleshoot phone book corruption on your phone.
I have a Parrot MKi9200. Since a few weeks I cannot play music correctly. I connect my phone with Bluetooth so I can play Spotify. This always went correct. But now It stops during the first song and says not provided. I tried disconnecting my phone, set the settings back but it all doesn’t work.
What can be the problem of this?
Thank you
Hello Emmy,
Is this issue with an iPhone ?
Could you try a different phone ?
What software version is on the MKi9200 ?
Regards,
Philip
When trying to reset it to factory settings, I’m asked “do you want to delete all memory” but no button can be used to confirm.
To accept reset you need to press the Green button.
Hi, my Parrot mki9200 displays ‘not provided’ every few minutes en then the radio mutes for a few seconds. I can’t find a solution online. Do you know how to solf this problem?
Hello Herman,
This is an unknown issue. Have seen many, many hundreds of MKi9200’s and never seen this on the display.
Does the MKi9200 still do it if your phone is not connected (turn off Bluetooth to test) ?
Did the phone book sychronise correctly (when connected) ?
Have you tried pairing without phonebook sync ( to test) ?
Regards
Philip
Where can I download the latest Software Update for my parrot MKI9200.
Would appreciate a link if possible
DO NOT “update” version 3 firmware – you will destroy the Parrot control box.
Please see this link for the updates to version 1 and 2 control boxes:
https://www.justcarkits.co.uk/product-category/software-updates/
I have a 9200. The screen has stopped working. It sometimes connects to the phone and other times doesn’t, and the screen is sometimes on and sometimes off.
Do I need to replace the head, and if I do can i just plug the new one on?
Couple of things to check before replacing anything.
Find control box. If software label shows V1.00, V1.01 or V1.02 you will need the old display (very unlikely to find one). Do not put a newer version display on this control box version as it will destroy it.
Check with multimeter that you have 12V (red), Ignition (orange) and Ground (black) and these are not intermittent connections.
Also look at display cable & socket. There should be 5 pins on display cable and all should be same height in housing. Then check the pins on control box display port and make sure one is not pushed back. This issue causes intermittent re-starts on the MKi9200 – have seen it many times.
Hi there , I have a Parrot MKI9200 , everytime I play music or exit a screen from the menu the speakers make a loud pop , as if it letting you know I have exited a certain screen etc.
My question is , can this be muted as I’m worried incase my speakers pop.
TIA
Riz
Vehicle model / make / year ?
Does it have an amplified system ?
I have a mki9200 the sound does not play connects fine but no sound coming from speakers radio in car plays fine so not the speakers any suggestions please
Morning Mark,
I am assuming the handsfree audio comes through the front speakers and is working correctly.
The music output from the MKi9200 can be wired to use the Aux input on the car stereo. Whether this has been done depends on the vehicle make / model / year.
To set this option it is in Settings / Audio / Mute On Streaming and the box should be unticked. Remember to select Aux on car stereo for music playback.
If you are not able to use Aux / not wired to Aux input then Mute on Streaming should be ticked. The Mki9200 will then use it’s own amplifier and go directly to the car speakers.
Hi, my display turning off suddenly sometimes. Firm. V2.20. Dont know why.. Maybe display or power cabel?..
Hello Tomas,
The MKi9200 will power down if the display is disconnected
Couple of things to check:
1. Check spring tension on Parrot fuseholders – they can be too weak ( pull spring apart slightly)
2. Check display cable where it plugs into the control box. Make sure all the pins on control box socket are same height and the same goes for the 5 pins in the display lead.
3. Depending on vehicle check wiring harness and connection for ignition on/off for poor joints / loose wires. If you find any scotch locks remove them and crimp or solder connection(s). Scotch locks are a great source of intermittent faults.
My screen has gone black on my MK i9200 so do I need a new screen or does it some how need re booting?
Check power feeds to MKi9200 control box. Red = permanent 12V, Orange = ignition 12V.
Check display cable pins are not pushed in.
If these are OK, suspect control box failure.
Hi,
My dongle just stopped working for no reason. I replaced the batteries and tried restarting and reconnecting the dongle but nothing works.
Please help.
Morning Cuong,
Please see the following post. It will explain how to pair the remote:
Pair MKi remote
Hi
I have a parrot MKI9200 v1.96 which is in French language and I cant seem to change it to English.
I would like to change to v2.20 English.
Is there anywhere I can download it from please.
Please see the following link:
https://www.justcarkits.co.uk/jck_blog/product/parrot-mki9200-update-file-v2-2-uk/
dopo aggiornamento il display da errore hardware.Cosa fare ? sostituzione centralina?Non riesco a portarlo alle impostazioni di fabbrica in quanto il telecomando non interagisce con il display.
Hello Mico,
What version of Mki9200 software did you update with ?
As part of the update the display firmware is also updated when the MKi9200 re-starts after the update and it’s possible that this corrupted it.
It is more likely to be a display fault that a control box error.
Without the MKi9200 starting up normally you cannot access any of the menus to perform a factory reset, though this would still not help the display issue.
Regards
Impossible because it shows on the screen Hadware error and I can’t move anything in the controller, tell me to reboot my kit and after shows (hardware error)
Hello Luis,
Unfortunately, you have a hardware issue which can only be resolved by replacing the faulty part – appears that it is the screen itself.
Please note that if you have a control box with V1.00, V1.0.1, V1.0.2 or V1.0.3 the replacement screen is no longer available and you MUST NOT use a screen from the new version as the control box will destroy it.
Parrot Parts